No products in the cart.
Electronic Parts, Module
18650 Li-ion 1S BMS Module (3A)
Availability:
Out of stock
- High-accuracy voltage detection circuit;
- Terminal of the charger using high voltage device;
- Built-in three-stage over-current detection circuit (over-current 1, over-current 2, load short circuit);
- MOS transistor can control the battery charge and discharge;
700 Ks
Out of stock
This is a 1S 3.7V 3A Lithium Ion BMS Module. This module is charging and protection module for Single Cell Lithium Ion or Lithium Polymer Battery. It provides the overcharge, over discharge and overcurrent protection. The charging voltage must be 4.2V. The module is very small in size and can be fixed directly with the battery. The 1S 3A Lithium Ion BMS Module starts the charge or discharge with some delay after the protection trigger has been removed.
Connection:
B + Connect with battery positive.
B- Connect with battery anode.
P + Input/output positve
P- Input/output negative
- Over charge voltage: 4.25±0.05V
- Over charge release voltage:4.23±0.05V
- Over discharge voltage:2.54±0.1V
- Maximal continuous charging current: 2A
- Maximal continuous Discharging current: 2A
- Over current protection: 3A
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
- Electronic Parts, Module, Detection & Sensor Module
Raindrop Detection Sensor Module
108 in stock- The LM393, use of the wide voltage comparator
- Provide both digital and analog output
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- The sensor uses the high-quality FR – 04 double material, the large area of 5.5*4.0 CM
- Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance
- The comparator output, signal clean, good waveform, driving ability is strong, for more than 15mA
- With potentiometer sensitivity adjustment
- The output format: digital switch output (0 and 1) and analog AO voltage output;
- Has a fixed bolt hole, convenient installation
SKU: EAP-000001 - Electronic Parts, Module, OLED Display Module
0.96 OLED Display Module (128×64) (Blue)
out of stock- Work perfectly well without the need of back light.
- 128*64 high resolution, ultra wide viewing angle
- Super low power consumption–only 0.08W when the whole screen lights up and 0.06W when displaying characters
- Fully compatible with multiple controlling chips including Arduino and more.
- Support a wide range of voltage input
SKU: EAP-000019 - Electronic Parts, Module, Detection & Sensor Module
HTU21D Temperature and Humidity Sensor Module
In StockElectronic Parts, Module, Detection & Sensor ModuleHTU21D Temperature and Humidity Sensor Module
22 in stock- Uses the I2C interface
- Typical humidity accuracy of ±2%
- Typical temperature accuracy of ±0.3C
- Operates from 0 to 100% humidity but this sensor isn’t recommended for harsh environments where it could come in contact with water (such as rain)
- 3.3V sensor – use inline logic level converters or 10k resistors to limit 5V signals
- Only one HTU21D sensor can reside on the I2C bus at a time
SKU: EAP-000002 - Electronic Parts, Development Board, ESPRESSIF(ESP)
ESP32-Cam Development Board
9 in stock- Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
- Low-power dual-core 32-bit CPU for application processors
- Up to 240MHz, up to 600 DMIPS
- Built-in 520 KB SRAM, external 4M PSRAM
- Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
- Support OV2640 and OV7670 cameras with built-in flash
- Support for images WiFI upload
- Support TF card
- Support multiple sleep modes
- Embedded Lwip and FreeRTOS
- Support STA/AP/STA+AP working mode
- Support Smart Config/AirKiss One-click distribution network
- Support for serial local upgrade and remote firmware upgrade (FOTA)
SKU: EAP-000024
There are no reviews yet.